网站首页 >> 产品中心 >>  >> 电力监控与保护 >> ARTM-8L温度传感器

温度传感器

  • 设备型号:ARTM-8L
  • 更新时间:2024-02-29

ARTM-8L温度巡检仪可接入NTC、PT100/PT1000、热电偶传感器、0~5V输入,主要适用于多路温度的测量和控制,应用于低压电气接点、变压器绕组、电机绕组等场所测温。

ARTM-8L温度巡检仪可接入NTCPT100/PT1000、热电偶传感器、0~5V输入,主要适用于多路温度的测量和控制,应用于低压电气接点、变压器绕组、电机绕组等场所测温。

ARTM-8L temperature inspection instrument can be connected to NTC, PT 100 / PT1000, thermocouple sensor, 0~5V input. It is mainly suitable for temperature measurement and control of multiple channels, and applied to temperature measurement of low voltage electrical contact, transformer winding, motor winding and other places.

 

1.1  ARTM-8L

Figure 1.1  ARTM-8L

1.2 技术指标

1.2 Technical Features

 

 

                技术指标

              Technical

功能

Function            

指标

Features

ARTM-8L

测量通道数

Number of channels measured

 

8

输入信号

Input signal

NTCR25=10.00kΩB25/50=3380K

NTCR25=50.00kΩB25/50=4150K

NTCR25=100.00kΩB25/50=3950K

NTCR25=30.00kΩB25/50=3950K

PT100/PT1000三线制;

PT100/PT1000Three-wire system;

热电偶支持KTJEN型;

Thermocouple supports K, T, J, E, N types;

0~5V

 

 

 

 

 

 

测温范围

Measurement Range

 

NTC-40℃140℃

PT100最大支持-200850实际范围视PT100定;

PT100: Maximum support -200℃850℃, the actual range depends on PT100;

PT1000最大支持-200850实际范围视PT1000定;

PT1000: Maximum support -200℃850℃, the actual range depends on PT1000;

热电偶:最大支持-2001372实际范围视热电偶型号定。

Thermocouple: maximum support -200℃1372℃, the actual range depends on the thermocouple model.

精度等级(标准信号)

Accuracy class (standard signal)

NTC±1℃

PT100/PT1000-200℃~200℃±1℃+200℃~850℃±1%

热电偶1%

Thermocouple: 1%;

0~5V0.5%

辅助电源

Auxiliary power

电压

Voltage

AC85~265V/DC100-300V

功耗

Power

<=2W

报警输出

Alarm Output

路数

Channel

5组常开

5 groups of normally open

容量

Capacity

AC250V/5A,DC30V/5A

温湿度输入

Temperature and humidity input

路数

Channel

1(选配)

1 (optional)

环境温度

Temp

±1℃

环境湿度

HUM

±3%

变送输出

Transmit output

路数

Channel

3

变送范围

Transmission range

4~20mA

通讯

Communication

协议

Protocol

MODBUS-RTU

接口

Interface

RS485

波特率

Baud rate

2400,4800,9600,19200

环境要求

Environment

 

工作温度

TEMP

-20℃~55℃

工作湿度

HUM

<=95%

1.3 产品安装及尺寸

1.3 Product Installation and size

ARTM-8L温度巡检仪装置采用面板嵌入式安装采用导轨(DIN35mm)安装方式。嵌入式安装首先柜体盘面上制作规定尺寸的正方形槽孔,装置取下支架后嵌入槽孔,再将支架推入卡槽锁紧即可。

ARTM-8L temperature patrol meter device adopts panel embedded installation or adopts rail (DIN35mm) installation method. Embedded installation first of all the cabinet plate to make the prescribed size of the square slot hole, the device to remove the bracket embedded in the slot hole, and then push the bracket into the slot lock can be.

1.3.1 安装方法

1.3.1 Installation method

 

 

1.2  ARTM-8L嵌入式安装

Figure 1.2  ARTM-8L embedded installation

 

 

1.3  ARTM-8L导轨(DIN35mm)安装

Figure 1.3  ARTM-8L rail (DIN35mm) installation


留言框

  • 产品:

  • 您的单位:

  • 您的姓名:

  • 联系电话:

  • 常用邮箱:

  • 省份:

  • 详细地址:

  • 补充说明:

  • 验证码:

    请输入计算结果(填写阿拉伯数字),如:三加四=7
上一篇 : ARTN-8温度巡检仪    下一篇 :  ARTM-24温湿度传感器

安科瑞电气股份有限公司主营产品:水电预付费系统,远程预付费电表,数显多功能电表
联系人:王璐月 手机:18321900706 传真: 地址:上海市嘉定区育绿路253号
sitemap.xml 技术支持:智能制造网 管理登陆 ICP备案号:沪ICP备05031232号-31